Contract orthotic manufacturing · Ipswich, QLD

The craft of a corrected cast.
The consistency of digital design.

Custom foot orthoses manufactured for podiatry clinics. Our in-house digital design process reproduces the geometric correction of a hand-balanced plaster positive using the patient's own 3D scan. We design, 3D-print, hand-finish, package and dispatch the device for your clinic to fit.

Send your first scan

The balance is a defined geometric operation on the patient's own scan, held to half a millimetre - not a template applied to it.

Manufactured on site in Ipswich, Queensland.
Direct contact with the people making your orthoses.
A finished Stratum orthotic seen from the side, showing the arch profile and the layered edge of the device.
A finished device in side profile — the corrected arch, the layered edge and the finished trim line.
Manufacturing lead times

Built to your schedule.

All figures are working days for manufacturing. Courier time is additional.

5days

Standard orders

Manufacturing turnaround

3days

Recovers & repeat pairs

Manufacturing turnaround

2days

Express service

Manufacturing turnaround

The geometry behind the orthotic

The corrected positive cast. Reproduced digitally.

The balance is a defined geometric operation on the patient's own scan, held to half a millimetre - not a template applied to it.

Defined geometric tolerance
0.5mm
Corrected cast tolerance relative to the source scan, in every axis.

A design-stage measure. Not a printer specification.

The corrected digital cast is held to 0.5 mm of the patient's source scan in every axis. Plantar surface smoothing is prohibited in the correction process.

This is a defined property of our digital design process. It describes the corrected cast geometry, not scanner accuracy or the dimensional accuracy of the finished printed device.

The geometric tolerance is a design-stage specification and is not a claim about clinical outcome.

01

A corrected digital positive cast

The patient's 3D scan becomes a corrected digital cast: the digital equivalent of the plaster positive traditionally balanced by hand. The orthotic shell is designed against that corrected surface.

02

Forefoot balance from the scan

Forefoot varus and valgus are measured from the patient's own scan, in millimetres and degrees, using the true first-to-fifth metatarsal head height difference. The measured forefoot-to-rearfoot relationship informs the correction.

03

Forefoot tilt is preserved

Scan alignment is yaw-only. The patient's actual forefoot tilt is retained rather than being flattened to a reference plane during alignment.

04

Controlled surface geometry

The corrected cast is held to 0.5 mm of the source scan in every axis. Smoothing is forbidden on the plantar surface, preserving the geometry used to construct the corrected cast.

The plaster-cast method is the reference.

In traditional orthotic manufacture, a technician reads the forefoot-to-rearfoot relationship from a plaster positive and adds plaster to create the corrected surface over which the device is formed.

Our lab developed its own digital design software to reproduce that balancing operation. The resulting geometry was developed against, and matched to, an annotated hand-balanced plaster positive from our own lab.

The clinical prescription still determines the required correction. The digital workflow makes the resulting design geometry reproducible, including when a repeat pair is manufactured from the stored design file.

Clinic-to-lab workflow

Digital where it matters. Finished by hand.

The design and manufacturing stages are digital. Finishing, packaging and final preparation are carried out by hand. Your clinic retains the prescription and fits the finished orthoses to the patient.

01 / INPUT Digital

Scan & prescribe

Capture the patient's 3D foot scan and specify the orthotic prescription. Email the scan and prescription to Stratum.

02 / DESIGN Digital

Correct & design

The scan is balanced to produce the corrected digital positive cast. The shell, heel cup, posting, arch fill and trim lines are designed to the prescription.

03 / BUILD Digital

3D-print the shell

The prescribed shell is manufactured using 3D printing at our Ipswich facility.

04 / FINISH By hand

Finish & dispatch

The orthoses are hand-finished, fitted with the prescribed finishing components and top cover, bagged and dispatched to your clinic.

Ready to start? Email us your patient's 3D scan and orthotic prescription.

First-scan details ↗
One pair, five stages

A scan goes in. A device comes out.

Every pair takes the same five steps. The first four are our own design software — written here, by the podiatrist who uses it — captured while a real pair went through it. The fifth is what came off the end of it.

How the design works ↗

  1. Two scanned feet shown as 3D meshes in the lab's design software.
    01 / Scan

    The feet as they arrive

    Your 3D scan, opened at the lab. Nothing has been corrected yet — this is the foot as the scanner captured it.

  2. A pair of corrected digital positive casts, shown as solid blocks with a contoured upper surface.
    02 / Balance

    The corrected digital cast

    The scan balanced into the digital equivalent of a corrected plaster positive. The device is designed against this surface, not layered onto the raw scan.

  3. The lab's design software, showing the prescription controls down the left and the pair of shells in the viewport.
    03 / Design

    Built to the prescription

    Heel width, forefoot width, arch height, skive and trim line, set to the figures you sent and applied to each foot on its own.

  4. The finished pair of orthotic shells seen from underneath, before manufacture.
    04 / Shell

    The shell, from underneath

    The finished geometry, checked from below before anything is printed. This is the file the printer receives.

  5. A finished Stratum orthotic seen from the side, showing the arch profile and the layered edge of the device.
    05 / Device

    The end product

    Printed, hand-finished, trimmed and topped at the lab in Ipswich, then bagged and posted to your clinic.

A part-printed orthotic shell on the print bed, the nozzle laying down the next pass.
A shell part way through its build, on the bed at the lab.
Manufacturing capabilities

Designed to the prescription. Finished to the specification.

Stratum manufactures orthoses in TPU and carbon-fibre polypropylene, with five shell firmness levels and further customisation available. Shell design and finishing options are specified to suit the referring clinician's prescription.

Shell materials

TPU and carbon-fibre polypropylene. Five shell firmness levels, with further customisation available.

Rearfoot posting

Prescription-based rearfoot posting, including intrinsic and extrinsic posting options.

Shell geometry

Heel cup depth, arch fill, trim lines and prescribed modifications.

Prescription additions

Options including medial heel skive and other prescribed additions.

Top covers

A range of top cover materials and finishes for the prescribed device.

Repeat manufacture

Stored digital designs allow repeat pairs without a new foot scan.

Request the price list
Inside the lab

Fourteen seconds of one shell printing on the belt at the lab — real speed, not a time-lapse. No narration and no music — press play if you want to see the machine your prescription ends up on.

A shell printing on the belt at the lab. Fourteen seconds, silent.
Digital workflow compatibility

Know what you can send before you change labs.

Before moving manufacturing, a clinic needs to establish whether its existing scanning workflow can supply files the lab accepts.

Stratum accepts iMed, STL and 3MF. If your scanner exports any of the three, your existing workflow already works and nothing in your clinic has to change.

View scan compatibility

Scanning on an iPad or iPhone with 3DSizeME or DolaApp? Send the iMed file exactly as the app exports it.

Accepted scan files

.iMed
3DSizeME and DolaApp iPad scans, sent as exported.
.stl
Binary or ASCII, from any 3D scanner.
.3mf
3D Manufacturing Format. Carries its own units, so nothing is assumed about scale.

Email scans to the lab with your own patient reference in the subject line. That reference is what matches the files to the prescription.

Working with Stratum

A local manufacturing partner. A repeatable design.

Contract orthotic manufacturing should allow the clinic to retain control of its prescription and patient relationship while outsourcing the manufacturing work.

Direct access to the lab

Stratum is a small manufacturing operation based in Ipswich, Queensland. One phone number connects your clinic to the people making the device, rather than an interstate call centre.

Repeat the stored design

The corrected cast and orthotic design can be retained as a digital file. Repeat pairs are manufactured from that stored design, without requiring a new scan. The original design geometry is therefore available for repeat manufacture.

Your clinic's identity

Clinic-branded packaging is available. Finished orthoses can arrive carrying the referring clinic's name rather than Stratum's. The clinical relationship remains with your clinic.

Start with one prescription

Send a first scan.
Assess the result in your own clinic.

If you have a compatible 3D scan and an orthotic prescription ready, email them directly to Stratum. We will manufacture the prescribed device, hand-finish it and dispatch it to your clinic.

If you are evaluating Stratum as a manufacturing partner, request the options and price list first.

Manufactured on site in Ipswich, Queensland.

Contact the lab directly

Send a first scan

Email the patient's 3D scan and prescription. Please confirm file compatibility before submitting the order.

Request the price list

Ask for the current manufacturing options, prescription additions and clinic price list.

Discuss a prescription

Contact the people manufacturing the orthoses directly to discuss your requirements.

admin@stratumlab.com.au
0404 076 312

68 Warwick Road, Ipswich QLD 4305